instrukcja VAG-COM EN, - rozne ❎ Diagnostyka Pojazdów
[ Pobierz całość w formacie PDF ]
VAG-COM
Diagnostic Software for VW/Audi/SEAT/Skoda
User’s Manual
Version 409.0
See our Website for an Interactive Online version of this manual:
Copyright (c) 2000-2004
by Ross-Tech, LLC.
920 South Broad Street
Lansdale, PA 19446
www.Ross-Tech.com
Disclaimer:
All rights reserved, No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written permission of Ross-Tech, LLC. The information contained herein is designed
only for use with VAG-COM. Ross-Tech, LLC. is not responsible for any use of this information as applied to this or other diagnostic equipment.
Neither Ross-Tech, LLC. nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred
by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this
product, or failure to comply with Ross-Tech, LLC’s written instructions.
By using VAG-COM, you acknowledge that this Program is provided "as is" and "with all faults, defects and errors" and that all use of the Program is at
your own full risk. It has been extensively tested, but we cannot guarantee it will work correctly with every system in every car. We will make our best
effort to fix any bugs and to enhance the program, but we specifically disclaim any liability for damage to your computer or your car, and we do not
promise to have any particular enhancements available on any specific date.
Copyright © 2004 by Ross-Tech, LLC
VAG-COM
Table of Contents
Getting Started
2-5
Main Screen
6
Select Control Module
7
Open Controller Function Screen
8-9
Fault Codes
10
Measuring Blocks
11-12
Data Logging
13-14
Single Reading
15
Readiness
16
Advanced ID
17
Login
18
7-digit PIN/SKC Dialog
19
Basic Settings
20-21
Output Tests
22
Recode
23-24
Adaptation
25-26
Security Access
27
Auto-Scan
28-29
Control Module Finder
30
OBD-II
31-32
Applications
33
Options
34-36
About
37
Appendix A: Problems & Issues
38-40
Appendix B: FAQ (Frequently Asked Questions)
41-54
Appendix C: VAG-Scope
55-57
Appendix D: TDI Timing Checker
58
Appendix E: VAG Functions
59
1
VAG-COM
Getting Started
VAG-COM allows you to turn a Windows-based PC into a sophisticated diagnostic tool for
VW/Audi/SEAT/Skoda models from 1990-2005.
(Go to our website
www.ross-tech.com
to download the latest version of VAG-COM. Click on:
“Download VAG-COM Software”.)
Connect the Serial or USB end of Interface to
the Serial or USB port on your PC. If your PC is
further from the vehicle than 6 feet, connect a
Serial Extension Cable between the PC and the
Interface (USB is not extendable). G
H If you are using a Serial Interface, you can skip to page 4 of this manual. If
you are a USB Interface, this message should pop up.
Click on the Found New Hardware message and the Found
New Hardware Wizard should start up. Select "Install from
a list or specific location (Advanced)" then click [Next >] G
H This dialog should appear. Select "Search for the best driver
in these locations" Check "Include this location in the search:"
2
Getting Started cont.
Use the [Browse] button to find the VAG-COM
folder (Usually C:\Program Files\VAG-COM\,
unless you chose a different folder when you
installed the software) Click [OK] G
H Click [Next >] and this dialog should appear,
warning you that we haven't paid Microsoft a pound of
flesh to certify the driver.
You're going to have to click the [Continue Anyway]
button..:-)
When the dialog to the right appears, Click [Finish] : G
Note: If, for some reason, you installed your USB Interface without following the above instructions,
and VAG-COM does not work correctly, go into your PC’s Device Manager while the USB Interface is
connected. Find the “VAG-COM Compatible USB Interface” and delete it. Then, unplug the USB
Interface from your PC, wait 5 seconds and plug it back in. Proceed with the installation starting on
Page 2.
3
Getting Started cont.
Connect the car end of your Interface to your vehicle’s
Diagnostic Port. G
H If your vehicle has a 2x2 port (some pre-1996 vehicles), then use
a 2x2 Adapter between the Interface and the ports in the car.
Start the VAG-COM program on your PC through either the Start Menu or the
icon on your Desktop. G
4
[ Pobierz całość w formacie PDF ]